Knowledge Base - How To:- Remove the Rear bumper

Removing Rear Bumper

Tools:

  • Cross-head screwdriver.
  • Flat knife or similar.
  • 10mm spanner.


You can make this job a little easier for yourself if you have the rear raised – ramps would be ideal (I reversed up my makeshift ramps made from floorboards).

First, remove the boot carpet.  This is held in with around 9 plastic fasteners.  To release them press the centre part of the fastener with a small screwdriver or similar, then pull out the whole plug.
Unplug the connector behind the boot light.
Also, remove the long plastic trim nearest the rear (highlighted in purple in the pic).  This is held with 4 poppers so can just be pulled up (careful not to bend it too much).

picture1

With the carpet removed.

picture2

Good time to check for rust/damage/snakes etc.

picture3

Now disconnect both of the rear light clusters.

picture4

Disconnect the licence plate lights and the reverse lights.

picture5

Using a thin knife, remove the triangular piece of the rear lights.

picture6

Now you will see 2 screws, remove these.

picture7

With the rear boot lid open, remove the final screw shown.  Lights can now be pulled from the car – remember to push through the grommet & wiring from inside the car.

picture8

Remove the 2 screws for the centre panel, it can now be pulled out & up from the car as there are only 2 clips holding it in place now, don’t forget to push the reverse light grommet & wire through.

picture9

Centre panel removed.

picture10

Now to remove the side strips.  There’s a screw here at the top of the wheel arch.

picture11
And a nut inside the wheel arch.  Plenty of penetrating fluid on this.  Don’t be too surprised if the thread snaps.

picture12

Two more 10mm nuts on the inside of the boot.

picture13

And repeat for the other side.  The 2 nuts on the inside of the boot are a little more difficult to get to due to the aerial motor, but it’s still possible to get to.

picture14

Now for the most difficult bit, 12 plastic screws (8 on top, 4 underneath).

picture15

picture16

Unscrewing these seem to have no effect unless you ‘help’ them out.
Try prising them upwards while unscrewing.

picture17

Or, reaching underneath to push them up (don’t push the whole plug, just the threaded part).

picture18

The metal strip can now be removed.

picture19

Another 2 screws, one at each side.

picture20


Underneath, 3 plastic fasteners each side.  2 need to be removed, the other is just disconnected from the bumper.

picture21

Like thus.

picture22

Last screw, in the wheel arch.  This is quite tricky to get to, you will need a very short screwdriver, or you will need to remove the wheels.  Or what I did, I removed the detachable screwbit from my screwdriver and placed it within a rachet + socket (or a spanner will do).

picture23

Be careful removing the bumper.  I recommend you ease the plastic tabs loose that held the underside of the bumper to the car as you don’t want these to break.  And when lifting the bumper – ideally 2 people, 1 at each side.  But if you have to lift if yourself, stretch your arms and carry it from the corners – holding it from nearer the middle and you’ll realise how wobbly it is and may damage it.

picture24

With the bumper removed.

picture25

If you wish to remove the big sturdy (plastic!!) bar, then this is held in by 4 bolts inside the boot (covered up by foam material and rubber grommets).

picture26

 

JohnnyC

Copyright © by MR2 Owners Club All Right Reserved.

Details

Created : 2011-10-06 10:07:26, Last Modified : 2011-10-06 10:07:26

User Comments

Technical Disclaimer 

The MR2 Owners Club and its respective owners, editors and contributors make no representations about the suitability of the information contained in the documents, materials and related graphics published on mr2oc.co.uk  

By entering this site, you hold this site and it's affiliates not legally responsible for any damages due to advice given here. This site and it's affiliates takes no responsibility for consequences of any actions that arise from advice given. Any opinion is given with information provided by you and can not be taken as absolute.

All repairs should be undertaken by a competent and qualified technician. By using this site, you understand and agree that all advice given and followed are at your own risk and do not hold this site or it's affiliates responsible for any damages.