UK Rev5 NA to Gen3 Turbo
-
Topic author - Posts: 2858
- Joined: 29/11/10 19:50
- Years of MR2 Ownership: 10
- MR2's Owned: 3
- Location: UK
- Been thanked: 6 times
UK Rev5 NA to Gen3 Turbo
Job for the weekend...
I'm sure I can figure it out as the pinouts are written on the board and I have the 3rd gen 3SGTE engine manual with the ECU pin out guide etc in there. However if anyone on here has done this before and has the relevant info to hand that would be awesome and will save me a bit of time!
I want to do this using the UK Rev5 body loom (one that goes down the pass side) - I have the loom from the donor car but it has been 'modified' for fitment of an aftermarket alarm and as such it's a bit of a mess in places.
In any case, I'll try to remember to document the wiring bit as I've not seen any Rev5 specific guides for doing it this way.
Rev5 Sonic Shadow
-
Topic author - Posts: 2858
- Joined: 29/11/10 19:50
- Years of MR2 Ownership: 10
- MR2's Owned: 3
- Location: UK
- Been thanked: 6 times
Re: UK Rev5 NA to Gen3 Turbo
All sorted thanks to some advice from Luke @ Pacific Works
Surprisingly easier than I thought it would be!
Surprisingly easier than I thought it would be!
Rev5 Sonic Shadow
-
- Administrator
- Posts: 5190
- Joined: 17/05/04 1:00
- Years of MR2 Ownership: 18
- MR2's Owned: 1
- Gender: Male
- Location: Glenrothes: The Kingdom of Fife
- Has thanked: 45 times
- Been thanked: 117 times
- Contact:
Re: UK Rev5 NA to Gen3 Turbo
Good that it went smoothly, perhaps if you have time at some stage, you could write it up for KY2?
-
Topic author - Posts: 2858
- Joined: 29/11/10 19:50
- Years of MR2 Ownership: 10
- MR2's Owned: 3
- Location: UK
- Been thanked: 6 times
Re: UK Rev5 NA to Gen3 Turbo
I'll have to go back in and take some photos. If someone can provide a good photo of an unaltered Rev5 22pin body loom plug that would be a help as I didn't take a photo of it beforehand. The only thing that's not obvious is the FC pin from the Rev3 Turbo ECU. It doesn't exist on the Rev5 passenger loom to the ECU, you have to run it separately from the fuse box to the ECU. Looking for an unused wire on mine I can borrow to neaten that up, as my car doesn't have AC I may be able to take one of the AC wires and use that instead.
Rev5 Sonic Shadow
-
- Posts: 6729
- Joined: 13/02/07 22:02
- Years of MR2 Ownership: 13
- MR2's Owned: 6
- Real Name: Dan
- Gender: Male
- Location: Sandwich, Kent
- Has thanked: 8 times
- Been thanked: 4 times
-
Topic author - Posts: 2858
- Joined: 29/11/10 19:50
- Years of MR2 Ownership: 10
- MR2's Owned: 3
- Location: UK
- Been thanked: 6 times
Re: UK Rev5 NA to Gen3 Turbo
Yeah, there's two wires for AC available by the looks of it. Any idea where that comes out on the other side - does it go through the engine bay fuse box?
Job for Wednesday!
Job for Wednesday!
Rev5 Sonic Shadow
-
- Posts: 182
- Joined: 18/01/10 8:20
- Current Model: MK2
- Years of MR2 Ownership: 5
- MR2's Owned: 3
- Gender: Male
- Location: Yorkshire, England
- Has thanked: 2 times
- Been thanked: 3 times
- Contact:
Re: UK Rev5 NA to Gen3 Turbo
Hi @SonicSW20 did you ever get round to doing a Pin out for the Rev5?
I'm in the middle of the same conversion now and trying to sort some niggles, I don't have the Rev5 ECU so I'm just looking for a diagram or even a picture from the inside of the Rev5 ECU.
I'm in the middle of the same conversion now and trying to sort some niggles, I don't have the Rev5 ECU so I'm just looking for a diagram or even a picture from the inside of the Rev5 ECU.
- MR2 Rev5 2.0 GTi TBar 2008 - 2011
- MR2 Rev5 Turbo GTS TBar 2020 - Present
- MR2 Rev3 Turbo GTS Donor car (RIP)
www.instagram.com/fuel_toyota
My Project thread
-
Topic author - Posts: 2858
- Joined: 29/11/10 19:50
- Years of MR2 Ownership: 10
- MR2's Owned: 3
- Location: UK
- Been thanked: 6 times
Re: UK Rev5 NA to Gen3 Turbo
Here's the pins:
never had time to sit down and write down what I did, long gone from my memory now!
never had time to sit down and write down what I did, long gone from my memory now!
Rev5 Sonic Shadow
-
- Posts: 182
- Joined: 18/01/10 8:20
- Current Model: MK2
- Years of MR2 Ownership: 5
- MR2's Owned: 3
- Gender: Male
- Location: Yorkshire, England
- Has thanked: 2 times
- Been thanked: 3 times
- Contact:
Re: UK Rev5 NA to Gen3 Turbo
Thanks mate, I have put the ECU Pin out into a google doc as I thought it may help someone in future.
I'll try add what I'm changing to the sheet as I go.
https://docs.google.com/spreadsheets/d/ ... sp=sharing
I'll try add what I'm changing to the sheet as I go.
https://docs.google.com/spreadsheets/d/ ... sp=sharing
- MR2 Rev5 2.0 GTi TBar 2008 - 2011
- MR2 Rev5 Turbo GTS TBar 2020 - Present
- MR2 Rev3 Turbo GTS Donor car (RIP)
www.instagram.com/fuel_toyota
My Project thread
-
- Administrator
- Posts: 5190
- Joined: 17/05/04 1:00
- Years of MR2 Ownership: 18
- MR2's Owned: 1
- Gender: Male
- Location: Glenrothes: The Kingdom of Fife
- Has thanked: 45 times
- Been thanked: 117 times
- Contact:
Re: UK Rev5 NA to Gen3 Turbo
top man, I'll add it to KY2 when your doneSynz wrote: ↑27/05/21 12:12 Thanks mate, I have put the ECU Pin out into a google doc as I thought it may help someone in future.
I'll try add what I'm changing to the sheet as I go.
https://docs.google.com/spreadsheets/d/ ... sp=sharing