Fires but won't run
Forum rules
Many subjects will have been discussed before. Please try the search function before starting a new thread.
Check in the Know Your 2 as the information you need may already be there.
Important ! - Please make your topic title as descriptive as possible . titles with just "help" generally dont get as many answers as a title that points to the problem
Many subjects will have been discussed before. Please try the search function before starting a new thread.
Check in the Know Your 2 as the information you need may already be there.
Important ! - Please make your topic title as descriptive as possible . titles with just "help" generally dont get as many answers as a title that points to the problem
-
Topic author - Posts: 2
- Joined: 18/03/20 20:42
Fires but won't run
Did an engine swap rev 3 na engine into a rev 2 na car. Engine fires for 2 seconds then dies. The loom was sorted to fit the new ecu, new plugs, igniter and coil changed, dizzy changed. Checked that no wires or earth straps have been left off. New fuel pump and filter, fuel flow checked. Nothing makes any difference.
Any ideas appreciated.
Any ideas appreciated.
-
- Posts: 848
- Joined: 29/01/11 18:53
- Years of MR2 Ownership: 9
- MR2's Owned: 1
- Real Name: Jan Olsson
- Gender: Male
- Location: Leicester
- Been thanked: 1 time
Re: Fires but won't run
Open up the ECU and check which terminal the IGF wire should (pin outs labelled on PCB) be then check it is correct in plug
Last edited by abovetherim on 01/06/20 12:47, edited 1 time in total.
1991 rev 1 T Bar n/a 3sge import. A work in progress!!!
-
- Posts: 848
- Joined: 29/01/11 18:53
- Years of MR2 Ownership: 9
- MR2's Owned: 1
- Real Name: Jan Olsson
- Gender: Male
- Location: Leicester
- Been thanked: 1 time
Re: Fires but won't run
I assume you found a guide for the wiring.
Just to note there are wiring changes in the engine bay fuse box and there should also be one wire that needs to come from body loom to engine loom but off the top of my head I can't remember which
Just to note there are wiring changes in the engine bay fuse box and there should also be one wire that needs to come from body loom to engine loom but off the top of my head I can't remember which
1991 rev 1 T Bar n/a 3sge import. A work in progress!!!
-
- Posts: 848
- Joined: 29/01/11 18:53
- Years of MR2 Ownership: 9
- MR2's Owned: 1
- Real Name: Jan Olsson
- Gender: Male
- Location: Leicester
- Been thanked: 1 time
Re: Fires but won't run
Also check the ECU part number as rev4 has immobiliser.
1991 rev 1 T Bar n/a 3sge import. A work in progress!!!
-
- Posts: 848
- Joined: 29/01/11 18:53
- Years of MR2 Ownership: 9
- MR2's Owned: 1
- Real Name: Jan Olsson
- Gender: Male
- Location: Leicester
- Been thanked: 1 time
Re: Fires but won't run
Check ECU part number is correct rev3 with no immobiliser
Open up ecu, on PCB pinouts are labelled, look for igf and check it is right.
I assume you found a guide. Fuse box changes and one of the wires from body loom plug needs to move to engine loom plug
Open up ecu, on PCB pinouts are labelled, look for igf and check it is right.
I assume you found a guide. Fuse box changes and one of the wires from body loom plug needs to move to engine loom plug
1991 rev 1 T Bar n/a 3sge import. A work in progress!!!
-
- Administrator
- Posts: 5227
- Joined: 17/05/04 1:00
- Years of MR2 Ownership: 18
- MR2's Owned: 1
- Gender: Male
- Location: Glenrothes: The Kingdom of Fife
- Has thanked: 49 times
- Been thanked: 124 times
- Contact:
Re: Fires but won't run
Sounds like it could be something to to with the COR (Circuit Opening Relay) If it was immobiliser related it wouldn't fire at all in my experience. You could try putting a temporary (very) link in the between +B and FP and see if it keeps running.
-
- Posts: 848
- Joined: 29/01/11 18:53
- Years of MR2 Ownership: 9
- MR2's Owned: 1
- Real Name: Jan Olsson
- Gender: Male
- Location: Leicester
- Been thanked: 1 time
Re: Fires but won't run
This is the wire that needs to move from body plug to engine plug I believe but my memory fails me, green wire iirc
1991 rev 1 T Bar n/a 3sge import. A work in progress!!!
-
- Posts: 848
- Joined: 29/01/11 18:53
- Years of MR2 Ownership: 9
- MR2's Owned: 1
- Real Name: Jan Olsson
- Gender: Male
- Location: Leicester
- Been thanked: 1 time
Re: Fires but won't run
Many years ago I helped a member out with this exact problem and it was igf needed moving one pin over.
On mine last year I had this issue, again it turned out to be igf but I was doing rev4 engine with rev3 ECU into rev1 car
On mine last year I had this issue, again it turned out to be igf but I was doing rev4 engine with rev3 ECU into rev1 car
1991 rev 1 T Bar n/a 3sge import. A work in progress!!!